TargetTalk

For those of that don't or can't drop the wrist as far for the Free Pistol, like a TOZ. Do you just cut the front sight height to where it naturally sits went you grip? The grip fits well and it seems easier to modify the front sight.

TIA

If you ONLY trim the front sight, your shots will be high. If you then lower the rear sight to get your shots back on track, you will be back where you started. Remember that the barrel (axis) and front and rear sight act as a unit. If it's a grip position issue, see if you can alter the grip angle by re-bedding the frame within the grip. Depending on your pistol, this will require some degree of chisel, Dremel and bedding compound work.

Bob

Good point! Didn't of it that way... Looks like I have some grip work to do.

"Looks like I have some grip work to do."

Yep!

When it came to adding any compound to my Morini’s grip I chickened out, or perhaps exercised caution, and used Blu-Tac to model the amount needed before photographing what I had done before stripping it off.
I would like to say I then made an excellent job of modelling the grip with Milliput but sold the pistol almost immediately when offered an Evo 10E.
I have yet to get round to altering anything on the Steyr’s grip but would do it again using Blu-Tac although I might try covering the grip with cling film first.
Jim

Grips are consumables in a sense. Having a fancy competition gun without a customized grip is like wearing glasses without a prescription.

Admittedly manufacturers don't help with this by doing things like colorful laminated grips that look like crap when adding material.

Not fitting grips is almost as stupid as buying fancy expensive "custom" grips that don't perfectly fit.

Putty 'em up; no one's looking at your damn grips.

Of course, if you're a Farklemeister then it's expected that the grips are glitzy.

Can always use a high quality colored grip compounds like this one https://sportshootingdepot.com/product/mec-compound/

I was mostly thinking of the multicolor laminated ones Walther likes to ship recently. There is just no way to make them look coherent once you modify them. With a walnut grip you can at least make it look somewhat consistent with the right color of two component wood filler.

+ 1

Bob

BobGee wrote: ↑Mon Jul 17, 2023 5:31 pm If you ONLY trim the front sight, your shots will be high. If you then lower the rear sight to get your shots back on track, you will be back where you started. Remember that the barrel (axis) and front and rear sight act as a unit. If it's a grip position issue, see if you can alter the grip angle by re-bedding the frame within the grip. Depending on your pistol, this will require some degree of chisel, Dremel and bedding compound work.

Bob

Hey Bob, you are here. What putty do you use? I’ve been using JB Weld Kwikwood similar to Selleys Knead it sold at Bunnings. It works fab~ but I bought some recently and found the ingredients might be changed. It’s softer and less dense, not as good as usual.

[/quote]

Hey Bob, you are here. What putty do you use? I’ve been using JB Weld Kwikwood similar to Selleys Knead it sold at Bunnings. It works fab~ but I bought some recently and found the ingredients might be changed. It’s softer and less dense, not as good as usual.
[/quote]

The new kwikwood compound is not as good as the old stuff.

I have been using this with a lot more success: https://www.amazon.com/dp/B000VPO0R8?ps ... ct_details

It is similar to the old kwikwood compound.

Oh you found the same that the new Kwikwood is not as good as the old. Cool, seems like not just me.
I’ll give that Quickwood a try. Thanks for that.

Here's a little trick that works for me. Instead of applying the putty directly to the grip, I first cover the area that I'm going to build up with a thin masking tape, and then apply the putty to the tape. It holds pretty well, doesn't move at all, but is easy to remove and leave the grip in its pristine condition.
I use Sugru, it comes in a bunch of different colors and is very easy to work with: https://www.amazon.com/Sugru-I000952-Mo ... B089WH4K6M

Another option is to use a Silicone Grip putty from Rink - it holds well but can be peeled away if needed without leaving any residue. This putty sets very quickly (~2 minutes) and it is brown so not sticking out much when applied to the walnut grip.

https://sportshootingdepot.com/product/ ... -silicone/

Thanks guys for all the choices.

Since you ask Todd (lwy.todd.lu), I've used Kwikwood and Selleys Plastic Wood Filler Cement. I prefer the former but a bit alarmed to find that it has changed. Will try the Quikwood stuff from Amazon next time I need to buy some (I still have a stash of Kwikwood).

Bob

Seems like I got lucky used the right product at the first place.
The new Kwikwood has a little bit longer work time and less density which I’m not sure if it’s a good thing or bad. The bad aspect is that the finish and the solidity is not supreme as the old one. But the good thing is that the weight feels lighter.
Anyway, I’ll get some Quickwood as replacement.

PS: tried Selleys Knead it. A little bit too epoxy and rubbery feeling. But good quality once it’s cured. The finish is very subtle. But one thing I don’t like is the colour which is light grey.

lwy.todd.lu wrote: ↑Fri Oct 27, 2023 1:23 am PS: tried Selleys Knead it. A little bit too epoxy and rubbery feeling. But good quality once it’s cured. The finish is very subtle. But one thing I don’t like is the colour which is light grey.

Hi Todd, if you review some of the YouTube clips of the elite shooters, you'll see that nobody worries about the colour of their filler - often plain white.

Bob

Ha~ true~
I’ve just had another look at the cured selleys. It feels harder and very fine. Filing and sanding is a bit harder then Kwikwood.