Page 2 of 2
Posted: Mon Feb 20, 2012 12:16 pm
by GaM
Guy,
I have a KK 200 PM from around the same era as yours and was interested in your comment about the bedding screws, can you please advise on the appropriate torque settings. Searching for this hasn't produced any results specific to the Walther aluminium stock!!!
Regards,
Gary
Posted: Tue Feb 21, 2012 4:07 pm
by gstarik
I use 6NM on both screws.
Posted: Thu Feb 23, 2012 6:29 am
by RobinC
6NM is also the torque we were recomended for and use on the new KK300 action screws by a top international shooter.
Robin
Posted: Thu Feb 23, 2012 8:09 am
by Johan_85
gstarik wrote:I shoot Walther kk200 since 1998.it's the best gun I ever had.
I had a Border barrel on it which shot almost 300000 rounds before I have replaced it with another Border few month ago.
I recommend to Walther shooters to use only the 2 front bedding screws and leave the back one out. The back screw have no real support,and the rifle shoots better without it.
If you use pillar bedding,than the back screw should be used.
The trigger is great,but you should check the head space every 10000 rounds,because it opens a little if you shoot a lot.
Guy.
Do you recommend those who shoot kk300 to use only the 2 front screws also?
When I look at the drawings on kk300 and kk200 they seem very similar where the screws are.
Posted: Thu Feb 23, 2012 11:41 am
by gstarik
Yes,when you use the aluminum stock use only the 2 front screws on both kk 200 and kk 300.
Guy.
Posted: Thu Feb 23, 2012 11:55 am
by Johan_85
gstarik wrote:Yes,when you use the aluminum stock use only the 2 front screws on both kk 200 and kk 300.
Guy.
Okey, thank you for a quick answer.
doubt
Posted: Tue Mar 20, 2012 11:49 pm
by Tonyarg
the front screws are the closest to the trigger? thanks[/img]
Posted: Wed Mar 21, 2012 1:25 am
by gstarik
The front screw is the one that goes through the recoil lug.the screw which is close to the trigger shouldn't be used.
Guy.
Posted: Wed Mar 21, 2012 8:39 am
by Tonyarg
Thank you very much!!
Posted: Wed Apr 04, 2012 5:53 pm
by Daytona Dad
Just the other day I shot my KK200 again only to re-discover what a great rifle it is (it been two years). Yes I own 5 of those other "A" rifles and none of them come close to the Walther. Weight, adjustment, feel, and trigger, I should mention it has been upgraded by dropping in a KK300 trigger, it's all great. If your not aware the KK300 trigger is a "Set Trigger" further reducing lock time.
As for options, it has the same rail as the other "A" rifles, I use a MEC Palm Rest for offhand and the MEC hand stop for others. The front barrel sleeve is cut for a Walther front sight and an "A" rifle sight (just flip it 180*). Same for the rear sight rail, its cut for "A" sights, so on top of riser blocks sits a Gehmann 595 sight with adjustable iris and a 526 in front. Butt plates too are interchangeable prone I use the Walther, kneeling I have a MEC, and off hand a "HPS Gemini" butt plate.
And this is a left over rifle, a hand-me-down from my oldest boy who upgraded to the Walther KK200 with the factory Border Barrel. If I had to do it all over again I'd walk past all the "A" rifles and go right to the Walthers.
Yes, I also shot a Walther LG300 and a GPS, maybe I'm a little bias .....
Hope this helps give you direction.
Posted: Sat Jun 02, 2012 6:59 am
by Maxicooper
Bntarrw wrote:I bought a KK 300 for my son and it has outstanding! Parts and service has never been a issue. I highly recommend it
I'm getting into Walther world. Who do you recommend for doing service? Please advise. Thank you.
Posted: Sun Jun 03, 2012 9:36 am
by Bntarrw
Just had a small issue with my sons and champions choice took care of us.