.32 S&W Long and WST powder?

If you wish to make a donation to this forum's operation , it would be greatly appreciated.
https://www.paypal.com/paypalme/targettalk?yours=true

Moderators: pilkguns, m1963, David Levene, Spencer, Richard H

Forum rules
If you wish to make a donation to this forum's operation , it would be greatly appreciated.
https://www.paypal.com/paypalme/targettalk?yours=true
Post Reply
Mike38
Posts: 34
Joined: Sat Dec 30, 2017 4:56 pm
Location: Illinois, USA

.32 S&W Long and WST powder?

Post by Mike38 »

Does anyone have reloading data, min-max, for reloading .32 S&W Long using 85 grain DEWC .315 cast bullets and Winchester WST powder? This will be shot in a Benelli MP95 Atlanta semi auto target pistol. I'm finding loads on the internet, but they are revolver specific and will not cycle a semi auto. I tried 1.6 grains, and had a 25% failure to extract and believe the slide is not moving fully to the rear. I loaded 20 more rounds using 1.9 grains but haven't shot them yet, am I on the right track?
fc60
Posts: 749
Joined: Fri Nov 25, 2005 11:46 am
Location: Western Washington State, USA 98385

Re: .32 S&W Long and WST powder?

Post by fc60 »

Greetings,

The Hornady Reloading book used to list tested loads for their 90 grain HBWC, now discontinued.

This would be a good starting point.

Make sure you use the HBWC data, not the SWC data. The bullets have different seating depths.

While WST is not specifically mentioned, you will be able to glean the maximum velocities of the other powders used.

Cheers,

Dave
TonyT
Posts: 267
Joined: Fri Aug 20, 2004 6:50 am
Location: Scottsdale, Arizona

Re: .32 S&W Long and WST powder?

Post by TonyT »

WST was Don Nygord's favorite powder for loading the 32 S&W Long wadcutters. I used his load in both a APdini SP and a Walther GSP before switching to N310. Unfortunately it has been over a decade since I used a 32 and I must have deleted the date from my files.
David M
Posts: 1676
Joined: Wed Mar 24, 2004 6:43 pm

Re: .32 S&W Long and WST powder?

Post by David M »

Home cast 90g button nose wadcutter with 1.8g WST gave me 760fps in both a Unique and Walther back in 2002.
currently using VV N310 1.5g same bullet in a Hammerli SP20 rrs.
divingin
Posts: 116
Joined: Fri Feb 20, 2015 5:08 pm

Re: .32 S&W Long and WST powder?

Post by divingin »

Culled this off the net some time back (the question marks were in the original file; the formatting was better than this shows, though.):


32 S&W long wadcutters loads for Walther GSP; COL: 0.920??0.969.

Bullet Weight Powder Weight, gr. Vel. fps Notes
Lapua HBWC 83 gr. HP?38 2.1?2.4 679?800
Lapua HBWC 83 gr. Bullseye 2.3?2.7 782?908
Lapua HBWC 83 gr. Titegroup 1.7?2.0 633?754
Lapua HBWC 83 gr. Unique 3.0?3.5 742?902
Lapua HBWC 83 gr. VV N310 1.7 807* *6-in barrel
Lapua HBWC 83 gr. VV N310 2.0 938* *6-in barrel
Hndy HBWC 90 gr. Bullseye 2.0?2.3 715?790
Hndy HBWC 90 gr. HP?38 2.1?2.4 744?831
Hndy HBWC 90 gr. Titegroup 1.9?2.1 765?818
Hndy HBWC 90 gr. Universal 2.4?2.7 777?844
Speer HBWC 98 gr. AA2 1.8
Speer HBWC 98 gr. Bullseye 1.6 674
Lapua HBWC 98 gr. Bullseye 1.7
Speer HBWC 98 gr. Bullseye 1.8 777
Speer L?HBWC 98 gr. Bullseye 1.8?2.2 765?780
Speer HBWC 98 gr. Bullseye 1.6
L?DEWC 100 gr. Bullseye 2.0 818
H&N .312 100 gr. Bullseye 1.7
Speer HBWC 98 gr. HP?38 1.9?2.3 718?861
Speer HBWC 98 gr. Titegroup 1.8?2.0 780?860
Speer HBWC 98 gr. Universal 1.9?2.2 675?830
Lapua HBWC 98 gr. VV N310 1.4 764* *6-in barrel
Lapua HBWC 98 gr. VV N310 1.9 843* *6-in barrel
Speer HBWC 98 gr. W231 1.8 718
Speer HBWC 98 gr. WST 1.5
Post Reply